Furniture Paint

by themissiah

Welcome!,This blog is about how do you paint furniture & buy furniture paint.
Q&A–: Which is better for painting furniture – oil or latex?
I’m painting a piece of furniture for the first time. Any suggestions or tips would be appreciated.

The answer in the following: (Hint: For answers, no site audit.)

Answer by sportygal
i guess latex is better.
To achieve a professional quality finish you must sand the wood smooth, repair all defects, and prime the surface before painting. You should also use the highest quality paint and brushes to obtain the best resultsTo produce smooth surfaces, always sand with the grain of the wood. The material should go through at least three sandings with successively finer grit sandpaper. Start with 80 grit, move to 150 grit and finish with 220 grit. Use a tack cloth to remove dust between sandings.
Raise the grain in the wood by rubbing it lightly with a damp cloth. Allow the wood to dry, and sand the raised grain smooth with 400 or higher grit sandpaper or synthetic steel wool. Use a tack cloth to remove any sanding dust.

Use a lamp or flashlight to set up a raking light (a light that shines on the project’s surfaces at a steep angle). Apply a light coat of denatured alcohol to each surface as you inspect it. Alcohol increases the bare wood’s sheen and highlights any areas that still need sanding or smoothing. Rub out any rough spots with synthetic steel wool. Wipe the material with a clean tack cloth to remove any dust

Use a high quality synthetic bristled brush to apply a light coat of water-based, enamel undercoating primer to your project. Allow the primer to dry according to the manufacturer’s instructions. Check the project one more time with the raking light and repair any imperfections.

Use a synthetic bristled brush to apply a light coat of latex (water-based) paint to your project. Allow the paint to dry according to the manufacturer’s instructions and recoat with paint until you are satisfied with the finish. When painting, it is always better to apply two thin coats than one thick one, to avoid runs, drips, sags and other potential paint problems.

For more protection, you can add a topcoat to your paint with two layers of water-based polyurethane.
Apply a thin coat with a synthetic bristled brush.
Allow the polyurethane to dry according to the manufacturer’s instructions.
Sand the topcoat lightly with 400 or higher grit sandpaper or synthetic steel wool. Remove any sanding dust with a tack cloth.
Brush on a second light coat of polyurethane and allow it to dry.

Choosing Paint
When painting indoors, use paint marked as “Interior” or “Interior/Exterior.” Exterior paint is not for indoor use. Plus it doesn’t dry as quickly and has a stronger odor — an important factor inside the house.

Sheen is the term used to describe the degree of light reflection a paint has. Usually the less sheen an interior paint has, the less stain-resistant it is. Different manufacturers may have various trade names for them, but in general sheens are classified as “Gloss,” “Semi-Gloss,” “Satin” and “Flat.”

Gloss is the toughest. It’s also an easier surface to clean, which makes it a good choice for areas of high traffic or constant use. Gloss is most often used on a home’s wood trim, baseboards and kitchen and bath walls. Gloss paint will, however, show imperfections in the surface more than other sheens.

Semi-gloss paints are also durable and easy to clean, but have less shine than gloss. They are just as suitable for woodwork, kitchens, baths and other high-traffic or high-humidity places.

Satin offers a good combination of easy-clean and moderate sheen.

Eggshell is a smooth, low-sheen finish that has less sheen than satin. It is ideal for living rooms, dining rooms, bedrooms and dens.

Flat paint is considered non-reflective and a good choice for large wall and ceiling areas. It also hides imperfections well and spatters less when applied.
Semi-gloss and satin are typically the best sheen choices for painting furniture.

Painting Tips and Considerations
Always use quality paint. Paints with higher concentrations of solids cover better, flow more evenly and help hide or reduce brush strokes.

Use the right brush. Synthetic bristle brushes are for latex (acrylic or water-based) paint and natural bristle brushes are for solvent-based paint.

Always use a primer. Primer adheres to wood surfaces better than paint. Primer also helps stop or reduce the effects of acids, pitch or tar that can migrate out of the wood and stain through your paint.

Brush with the wood grain. Brushing with the grain helps the paint flow more evenly and reduces the appearance of lap marks.

Allow the paint to dry completely between coats. Paint that hasn’t dried fully tends to have higher surface tension and restricts your paints flow.

Answer by nona
oil

Answer by ang
latex

Answer by DRAGON
spirit polish

Answer by Jack P
I’m not an expert but I’ve painted many floors. I believe that oil is more durable. If it’s an area that might get wet you will want to put something in the paint like Skid-tex. Painted floors can be very slippery when wet.

Answer by Tom Van Dyke
The difference between Latex or Oil has become a mute point now… I would use a latex because it cleans easier. The important consideration is Gloss or flat and the surface of the furniture. If it is covered with polyurethane or shellac, you will have to break up the surface with steelwool #1 grade or a sandpaper 200.
If you don’t then the latex will attempt to dry and slide into an alligator pattern which can be sanded but might need to be removed entirely with paint stripper.
Good Luck

Answer by juju
if it’s wood i would highly suggest a latex. sand it with a light sand paper and clean it up. better yet ( for wood ), you should stain it. if it’s outdoor furniture, like metal, i would suggest spraying it with a rustolium spray…sand it down first, then prime in, them spray the color after the primer is dry. allow about 24 hours to dry before applying another coat. i would not suggest staining when the weather is damp or humid, it doesn’t dry well. hope this helps

Answer by charlie_the_carpenter
Oil is much more durable but sometimes doesn’t flatten out as well as latex. Since you’re not used to doing it you should use latex. If you are going to paint with oil use a primer first.

Know better? Leave your own answer in the comments!

by themissiah

furniture painting

Q&A–: Painting furniture for a nursery?
I want to paint a small table and dresser for use in my son’s nursery. The paint I want to use is flat finish. Do I need to put a finishing coat after painting to protect the paint and furniture?

The answer in the following: (Hint: The answer is not necessarily.)

Answer by vinny
Semi-gloss or High-gloss paint is what is usually used on furniture.That makes it relatively resistent to spills, smudges, and small knicks.
If for some reason you must use the flat paint, you can put a coat of clear polyetheline over it.
I would just use a Semi-gloss enamel, and be done with it. 7/29

Answer by Rightside
Painting furniture you should use and alkyd primer and paint (oil based). Or you can also use a alkyd glaze. Make sure you fine sand between coats. Check Benjamin Moore Website to see more info. Use a semi gloss finish, this will give you a harder finish, which will not shine to much. Plus the finish will look smoother and not have a lot of brush marks. Good luck.

Know better? Leave your own answer in the comments!
_______________________

Beautiful:

finishedwhole

Image by kawaface
still needs hardware, but i think i’m done painting. maybe i’ll decide to add more to the top or something later…

___________________